Minimum Order Quantity | 1 Piece |
Motor Horsepower | 0.5 HP - 3 HP |
Brand | IPP |
Stages | Two Stage |
Motor Phase | Three Phase |
Pump Type | Horizontal Monoblock Pump |
Material | Cast Iron / Stainless Steel |
Condition | New |
Condition | New |
Condition | New |
*Your information is safe with us.
Condition | New |
Condition | New |
Many Option in Difference Operation:-
Condition | New |
Construction:-
Casing: Horizontal split upper and lower half polled and doweled together. Suction and discharge branches are cast integrally with the lower halt Removal of upper casing permits Inspection, maintenance and removal of entire rotating element without disturbing suction and discharge piping or pump and driver alignment. Upper half casing has seal water piping, priming and vent connection with vent cock and lifting lugs. Lower half casing contains topped openings for gauges and drainage. Nameplate Is stainless steel. Pump Is available in horizontal but also vertical installation.
Impeller: The impeller Is of the enclosed double suction Nib°, In one piece , providing hydraulic balance. All exterior surfaces are machine finished. Interior surfaces or water ways are smoothly. Impeller is accurately balanced and keyed to shaft.
Wearing Rings: Renewable cast iron casing wear rings are held in position by tongue and groove, engaging both upper and lower halves of [he casing, preventing leakage loss around the outside surface of these rings. Impeller wear rings can be furnished for large pumps, during maintenance, only replace impeller wear rings when it Is not necessary to machine the impeller.
Shaft Bearing: Grease lubricated ball bearings are standard for groups S and M, oil lubricated ball bearings are standard for group L. a pair of single row angular contact bearing Is standard for group LL and above. The thrust bearings are securely locked In the thrust bearing housing and take radial and unbalanced thrust load. The coupling end bearing is tree to float axially in the bearing housing and takes radial load only.. By the rotation of an oil ring, oil can be picked up to lubricate bearings, a constant level boiler maintains proper oil level In the housing
Flange Drilling: All suction and discharge flanges are drilled to PNI6 as standard. ANSI and JIS can be supplied by request. In pumps operating above 16 bar special flange drilling ( PN25) will be supplied.
Application:
*Your information is safe with us.
Condition | New |
Condition | New |
Condition | New |
The WXC pumps series comply fully to the European standard DIN24255. This standard covers both performance and dimensions. The WXC pumps series are used for pumping clean water of liquids with Characteristics similar to water. They are suitable for plants, mines, City water supplies, air-conditioning coolers, firefighting system and irrigation.
For a pump of same the model, the performance can be changed by Trimming the outer diameter of the impeller. Only four shafts are required to cover the total range, and this gives many common interchangeable parts for pumps filled to the same shaft Just like the shaft, the bearing house has only for sizes for the whole series.
The pump has a back pull-out design, and when a suitable spacer coupling is fitted to a direct coupled unit the casing and motor can remain in position while all other pump parts can be removed for simple and quick maintenance.
Applications
Working Conditions
Material:
Operating Range:
*Your information is safe with us.
Minimum Order Quantity | 1 Piece |
Temperature | 70 deg C |
Speed | 1450 rpm / 2900 rpm |
Voltage | 415V |
Frequency | 50 Hz. |
Condition | New |
Condition | New |
Model | Inlet Port Size | Outlet Port Size | Maximum Impeller Size | Maximum Capacity | Maximum Head | ||
3500 RPM | 1750 RPM | 3500 RPM | 1750 RPM | ||||
JP405 | 2 (51mm) | 1-1/2 (38mm) | 55 (140mm) | 30/h | 25/hr | 34m | 25m |
JP408 | 2 (51mm) | 1-1/2 (38mm) | 55 (140mm) | 38/hr | 32/hr | 38m | 26m |
JP609 | 2-1/2 (63mm) | 2 (51mm) | 63 (160mm) | 60/hr | 50/hr | 50m | 34m |
JP910 | 3 (76mm) | 2-1/2 (63mm) | 748 (190mm) | 80/hr | 66/hr | 70m | 50m |
JP915 | 3 (76mm) | 2-1/2 (63mm) | 748 (190mm) | 100/hr | 84/hr | 80m | 57m |
Condition | New |
*Your information is safe with us.
Condition | New |